160kVA, Three Phase, Lister Petter Open Standby Generator
Model No.: LLD160/3
The Lister powered LLD160/3 is a 160kVA three phase diesel generator. Complete with Crossley SLG series single bearing, 4-pole, brushless alternator, remote start/stop control system and 260 litre fuel tank. With Lister Petter’s legendary performance and reliability this water cooled generator is perfect for both stationary and prime power applications. Welling and Crossley carries out stringent factory testing including full load testing.
Alternator Model: Crossley SLG Series
Electric Power: Three Phase
Active Rating: 160 kVA at 0.8 pf (Standby)
Power: 128 kW
Electric Potential: 415V
Engine Model: Lister Petter GWTA6
Engine Speed: 1500 rpm
Cylinder No.: 6T
Cubic Capacity: 5.99 L
Bore / Stroke: 100 x 127 mm
Compression Ratio: 17.5 : 1
Starter Voltage: 12V
Flywheel ( Max. Continuous Power): 134 kW
Combustion Air Flow: 18.2 m³/min
Cooling Air Flow: 265 m³/min
Cooling System: Water Cooled
Heat Rejection to Cooling System: 136 kW
Exhaust Gas Flow: 43.8 m³/min
Exhaust Gas Temperature: 550°C
Fuel Type: Diesel
Fuel Tank Capacity: 260 L
Approx. Fuel Consumption (Continuous): 29.6 L/hr
Approx. Fuel Consumption (Standby): 31.3 L/hr
Dimensions (L x W x H): 2845 x 1070 x 1650 mm (L x W x H)
Weight: 2130 kg
*Specifications are subject to change without notice
The control starting system is fitted standard.
Starting is remote or local to the machine with push Start/Stop button and includes the following digital indicators:
- Oil Pressure
- Engine Temperature
- Volts and Amps
- Shut Down for low oil & temperature
- Emergency stop button
- Output circuit breaker
- Static Battery Charger
- Pump pressure reading
- Pump pressure pre-set cut out values PSI
- Generator operation mode
The control system has an auto start programmed run event system, and it can be configured to operate with an Automatic Transfer Switch with logic.
- Heavy duty fabricated steel baseframe
The complete generating set is mounted as a whole onto a heavy duty fabricated steel baseframe. Anti-vibration pads are fixed between the engine and alternator feet, and the baseframe, ensuring complete vibration isolation of the rotating assembly.
- Bunded Fuel Tank (AS 1940-2004 compliant)
The fuel tank is fully bunded and complies fully with relevant sections in AS 1940-2004. It has a secondary containment compound with a capacity as big or bigger than that of the tank, and is made of surface coated steel. This compound is designed to sufficiantly retain spillage and enable recovery of any spillage. For more information regarding AS 190-2004 compliance refer to the standard, or contact us.
- Battery Charger
This trickle charge battery charger ensures that your generator can start up when needed. It has both 12v and 24v charging capabilities.
- Control Panel with Emergency Stop button
This control panel monitors the controls of a single unit to achieve automatic start/stop, data measuring/monitoring, alarm protection and three remote systems (remote control, remote measuring and remote communication). The controller adopts large liquid crystal display (LCD) and has a 32 bit micro-processor with precision parameters for measuring, fixed value adjustment, time setting and threshold adjustment.
- Prime or Standby Power
Standby: kVA @ 0.8 pf These ratings are applicable for supplying continuous electrical power (at variable loads) in the event of a utility power failure. No overload is permitted on these ratings. Minimum output from alternators are peak continuous rated (as defined in 1SO 8528-3 @ 27°C. Annual hour limitation: 500 hours).
Prime (continuous): kVA @ 0.8 pf. (Divide standby rating by 1.1). Available for continuous electrical output. There is no hour limitation. 10% overload is available 1 hour in 12. The generating set and this specification is designed for environmental conditions of up to 27°C, up to 152.4 m above sea level and up to 60% relative humidity. Ratings at 0.8 pf.
For ratings outside this range, please contact us.